Package List:
1 * Solar Charge Controller
1 * User Manual (English)
Visual LCD graphic symbol, brief key operation.
Automatic identification system voltage level, intelligent PWM charge mode.
Adjustable charge/discharge control parameters, settable operating modes of loads.
Multiple selection of battery.
Adds current display function.

Features:
Solar Current: 30 Amps
Load Current: 30A
Voltage: 12/24V
Min. voltage to operate: 8V
Accuracy: 60mV
Has Digital Meter

What Comes Standard for ProStar Controllers:
Estimated 15 year life
PWM series battery charging (not shunt)
3-position battery select: gel, sealed or flooded
Very accurate control and measurement
Jumper to eliminate telecom noise
Parallel for up to 300 amps
Temperature compensation
Tropicalization: conformal coating, stainless steel fasteners & anodized aluminum heat sink
No switching or measurement in the grounded leg
100% solid state
Very low voltage drops
Current compensated low voltage disconnect (LVD)
LEDs indicate system status and various faults
Capable of 25% overloads
Remote battery voltage sense terminals

Functions:
1.Build-in industrial micro controller.
2.Big LCD display,all adjustable parameter.
3.Fully 4-stage PWM charge management.
4.Build-in short-circuit protection,open-circuit protection,reverse protection,over-load protection.
5.Dual mosfet Reverse current protection ,low heat production.

Features:
1. Floating charge Voltage(HVD 13.3V-15V)
2. Recovery after under Voltage(LVD 11V-13.5V)
3.Under Voltage protection (RVD 9V-12.3V)
4.Load Mode(24hours,1-23hours,0hour)
5.Battery Option (GEL,LEAD-ACID,FLOODED)

MODEL: KLD1230
Batt voltage: 12V/24V auto
Charge current: 30A
Discharge current: 30A
Max Solar input: <50V
Equalization: B01 sealed 14.4V
B02 Gel 14.2V
B03 flood 14.6V
Float charge: 13.7V(defaul,adjustable)
Discharge stop: 10.7V(defaul,adjustable)
Discharge reconnect: 12.6V(defaul,adjustable)
USB output: 5V/3A
Self-consume: <10mA
Operating temperature: -35~+60 degree C

Package:

1.1X 30A Solar Contorller
2.1X User Manual
Build-in industrial micro controller,Big LCD display,all adjustable parameter.
Dual mosfet Reverse current protection,low heat production.
The controller has a low failure rate and will last a long time and protected with moisture-tight coating, minimizing damage from humidity and from nesting insects.
Build-in short-circuit protection,open-circuit protection,reverse protection,over-load protection.
Easy to set up and operate. Suitable for home, industrial, commercial, boat, car etc.

Each INCC1205 charge controller comes with four green LED indicators and one red LED indicator displaying battery status, connection status and real-time battery charge capacity. The INCC1205 solar charge controller is in full conformance with both CE and RoHS standards and is backed up by a standard 2-year manufacturer’s warranty.

Specifications:

Rated solar input current: 5A
Rated output charging current: 5A
Charging voltage: 12.8V
Cut-off voltage: 14.6V
Float voltage: 13.8V Temp Comp. (mV/°C): -30mV/-60mV
Temperature: -31°F to 131°F

Package Includes:

Instapark INCC1205 12 volt / 5 amp Solar Charge Controller
Battery Terminal Clamps
5.5mm x 2.1mm female to bare wires (solar panel output) adapter
User manual
PWM (Pulse Width Modulation) technology with temperature compensation protects battery from over-charging
4-LED Battery charge status LED indicators
Suitable for both sealed and flooded lead-acid batteries & automatic voltage detection, 12 volts only
Maximum 5 amp under load, compatible with Instapark solar panels and many other manufacturers
Includes a plug-n-charge connection cable for the Mercury27 solar charger

Safety Instructions:
1.make sure your battery has enough voltage for the controller to recognize the battery type before first installation.
2.The battery cable should be as short as possible to minimize lose.
3.The regulation is only suitable for lead add batteries: OPEN, AGM, GEL it is not suited for nickel metal hydride, lithium ions or other batteries.
4.The charge regulator only suitable for regulating solar modules, Never connect another charging source to the charge regulator.

System Connection:
1.Connect the battery to the charge regulator – plus and minus.
2.Connect the photovoltaic module to the regulator – plus and minus.
3. Connect the consumer to the charge regulator – plus and minus.
The reverse order applies when deinstalling!
An improper sequence order can damage the controller!
Battery Voltage: 12V/24V auto & Charge Current: 30A & Discharge Current: 30A
Automatically manage the working of solar panel and battery in solar system. Use PWM mode, improve system efficiency and prolong the life span of the battery.
Build-in short-circuit protection, open-circuit protection, reverse protection, over-load protection.
Big LCD display, all adjustable parameter. Good heat dissipation
Easy to set up and operate, have a User’s Manual, suitable for home, industrial, commercial etc.

Product Specification:
• Charge Control Mode: PWM
• Rated Current : 60A
• Rated voltage: 12V/24V Automatic Identification
• Installation Cable Area: 4# AWG (20mm2)
• Maximum Voltage of solar panel: 48V 
• Float Voltage: 13.8V/27.6V 
• Low Voltage Disconnection: 10.7V/21.4V 
• Low Voltage Re-connection: 12.5V/25V 
• No load loss: <30mA
• loop voltage drop:<200mV
• Temperature compensation: -4mV/Cell/°C
• Operating Temperature: -10℃~60℃
• Storage temperature: -30℃~70℃
• Humidity Requirement: ≤90％
• Dimension: 128 mm×188 mm×61mm
• Mounting hole spacing: 98mm×178 mm –Φ5
• Net Weight: 720g

Package List:
• 1 x 80A Solar Charging Controller
• 1 x Temperature Sensor
• 1 x User Manual
Good to know:
• With 24 Months Warranty, Instantly Reachable Support.
Capacity: 80A PWM Solar Charge Controller For 12V/24V DC Input
Intelligent Lighting On/Off by Daylight Sensation and Timing Control
High Efficient PWM Charging & Power Saving
LCD Display: Simple and Intuitive Setting & Use,Various Load Control Mode Available
Intelligent Battery Protection System: Over Charging, Load Overload/Short Circuit,Short Circuit,Battery Reverse Polarity Protection

Specification::
• Rated voltage: 12V
• Rated charging current: 10A
• Rated load current: 10A
• Cut-in Voltage:13Volts
• Cut-out Voltage:14.2Volts
• Adjustable controlling parameter of the system
• Suitable for Home, Industrial, Commercial etc

Protection:
Over-load protection;Short circuit protection;Lightning protection; Under-voltage protection;Over-charging protection;Reverse Polarity protection

Note:
Never deeply discharge your battery
Never let your battery voltage pass below 11.0 volts
Use a DMM(DIGITAL MULTI-METER) to measure your battery’s voltage
Connect charge controller to the battery first and remove last
The charge controller is not waterproof,should be placed in a well ventilated dry area,free from flammable gases and moister

Package List:
• 1 x Solar Charge Controller
• 1 x User Manual
• 18-month warranty
Savings for you! The charge controller supplied by solar energy and have requirements power EMI indicator .For monitor the real-time currency, volt and electricity output volume statistics when charge or discharge is proceed
The product provides overcharge, over-discharge, overload protection, as well as short-circuit and reverse-connection protection.
Easy to set up and operate:Suitable for small solar energy system.
User friendly easy to read two led display shows that your battery is fully charge or is charging
What You Get: POTEK 1 solar charge controller,full 18-month Worry-Free Warranty and friendly customer service

Esky® – Sky of Electronics

Esky LMS2430 intelligent solar controller is equipped with industrial-grade STM 8 microprocessor to control the charge and discharge process and has perfect and reliable battery charge and discharge period management. This controller has multiple load control modes and is adaptable to different industries.

Features:
– Excellent heat balance design and natural air cooling
– 4-stage charge period management (EQU, Bulk, ABS, Float)
– Charging temperature compensation function
– Comprehensive and reliable load control mode can identify the day and night
– Multiple electronic protection
– Comprehensive and reliable load control mode can identify the day and night
– Well-designed charge loop can effectively improve the efficiency of charge and discharge, and reduce the heat consumption in charge and discharge

Specifications:
– System voltage of PV: 40V
– Maximum voltage of PV: 30A
– Maximum discharge current: 30A
– Maximum output voltage: 12V/24V
– Maximum output power: 360W/720W
– Compatible battery: lead-acid cell
– Charge way: 3-state PWM Charge
– USB Charge port: 5V 1A

Package Content:
– 1 x Esky Solar Charge Controller
– 1 x User Manual
– 1 x Warranty Card

Seller Warranty:
– 30-Day Money Back Guarantee
– 12 Month Replacement Warranty
– Lifetime Support Guarantee

Funtionality: equipped with industrial-grade STM 8 microprocessor to control the charge and discharge process. And, it has reliable battery charge and discharge period management
Technicals: max 30A 12V/24V 360W/720W, power rate adjustable with dual USB ports; 4-Stage(EQU, Bulk, ABS, Float) charge management and 3-Stage PWM charge
Easy to use: Comes with a 30x50cm LCD display that can clearly indicate the status and data, it can be conveniently switched modes and parameter configuration etc.
Mutiple electric protection: over-current and short-circuit protection, inverse connection protection, low voltage and overcharge protection